Darkglass

Darkglass Microtubes B7K Ultra V2 Aux - The Squid Limited

SKU: 4-DG-B7KU2S
Inclusief BTW.
€459.00

Wereldwijd slechts 1000 stuks beschikbaar: de monsterlijke SQUID van Darkglass - met Aux ingang!

Gloednieuw Darkglass pedaal! De geüpdatet uitvoering van de Microtubes B7K Ultra V2 - bijgenaamd "The Squid" - is gedecoreerd met prachtig artwork van Ignacio Bazan Lazcano, welke is aangebracht op het pedaal met een speciale graveertechniek. Dit limited edition effectpedaal borduurt voort op de eerdere uitvoering van de Microtubes B7K Ultra bass preamp en geeft de speler nu nog meer veelzijdigheid dan voorheen. Zo is er onder andere een gebalanceerde XLR output met selecteerbare speakerkast emulaties zodat je een volwaardig en groots amp-like geluid tevoorschijn kunt toveren terwijl je direct in de tafel of interface inprikt. Daarnaast kun je het pedaal verbinden met je Mac of PC via USB om zo extra cabinet simulaties in te laden. Tot slot vinden we ook een aux ingang terug op the B7K Ultra V2 The Squid zodat je je muziekdrager kunt aansluiten op het pedaal: ideaal om thuis mee te oefenen natuurlijk. Naast de uitbreidingen blijft de basis van het pedaal natuurlijk de ontzettend dikke bas pre-amp waardoor het zo geliefd is geworden onder veel muzikanten, en deze komt ook ontzettend goed tot zijn recht op je pedalboard. Zo is het overdrive circuit afzonderlijk van de krachtige pre-amp in te schakelen en in combinatie met de 4-bands EQ levert dit een groot scala aan dikke sounds op. Als kers op de taart zijn de verschillende EQ-banden ook nog eens te fine-tunen met de mini toggle switches voor precieze tone shaping, terwijl de Attack en Grunt siwtches bepalen hoe het hoog en laag worden beinvloed door het overdrive circuit. De blend knop geeft nog een extra stukje controle over de balans tussen je cleane geluid en het overstuurde signaal. Dit pedaal maakt dan ook moeiteloos de transitie van de woonkamer en de studio naar het podium, en biedt waar dan ook, wanneer dan ook, een monsterlijke toon.

  • Master: Whereas the Level Knob controls the output of the overdrive section the Master volume adjusts the overall volume of the unit. Ideal for fine tuning the output on clean mode. It also serves as a DI level control.
  • Blend: Mixes the clean input signal with the overdriven signal. The clean signal remains at unity gain while the volume of the overdriven signal is set by the Level knob, allowing for fine control of the blend ratio.
  • Level: Sets the volume of the overdriven signal.
  • Drive: Sets the amount of saturation in the overdriven signal.
  • Attack Switch: Sets the amount of treble content to saturate: The "Boost" setting emphasizes the treble content extra clarity and presence. The "Flat" position leaves this register untouched while the "Cut" position will reduce the amount of high frequencies being saturated.
  • Grunt Switch: Sets the amount of low frequency content to saturate by selecting between three different bass boost levels before the clipping stage.
  • Bass: +-12dB @ 100Hz
  • Lo Mids: +-12dB switchable 250Hz, 500Hz and 1kHz
  • Hi Mids: +-12dB switchable 750Hz, 1.5KHz and 3kHz
  • Treble: +-12dB @ 5kHz
  • Direct Ouput: Balanced XLR output for connecting the pedal to a microphone preamp, PA system etc.
  • Ground lift: Disconnects the signal ground on the Direct Output to break any ground loops. Set this switch to either position that has less noise. The switch does not affect the ¼” output.
  • Cab Sim: Toggle the cabinet simulation on/off on the Direct Output. This switch completely bypasses all digital circuits and allows you to get a zero latency signal when needed.
  • Headphones: B7K Ultra has an internal stereo headphone amplifier capable of driving a minimum load of 16 ohms from the 3.5mm stereo jack. Use the Master volume control to adjust the level.
  • USB: A Micro USB B connector allows you to connect the pedal to PC/Mac to load cabinet simulation impulse responses to the pedal and control various other settings.
  • Aux In: This 3.5mm stereo input allows you to practice with backing tracks from e.g. your smartphone or laptop. Auxiliary input can only be used with the headphone output. The pedal does not control the level, it must be set from your audio source. Remember to always first set the level low before connecting anything to the aux in!